1 ftr-k1 series n partnumber information jsl d 12 m n - k [example] (a) (b) (c) (d) (e) (f ) (a) r elay type jsl :jsl -series (b) coil type nil : 1 coil d : 2 coils (c) coil r ated voltage 12 : 3.....24 vdc coil r ating table at page 3 (d) contact confguration nil : 1 form c m : 1 form a (e) contact material n : agsno 2 , au plated (f) sealed type k : w ash tight n features l small footprint - width: 10mm - height: 12.5mm l high insulation - insulation distance: 8 mm (between coil and contacts) - dielectric strength: 5,000 vac (between coil and contacts) - surge strength: 10,000 v (between coil and contac ts) l plastic materials - ul 94 fame class v-0 l plastic sealed type l cadmium free relay l lead-free relay l rohs compliant. please see page 5 for more information power relay 1 pole - 8a polarized latching type jsl series
2 ftr-k1 series n specification * minimum switching loads mentioned above are reference values. please perform the confrmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. jsl series item jsl (1 coil) jsl (2 coils) contact data confguration 1 form a, 1 form c construction single material agsno 2 + au plated resistance (initial) max. 100 m at 6vdc, 1a contact rating (at resistive load) 8a, 250vac / 24vdc max. carrying current 10a max. switching voltage 400vac / 150vdc max. switching power 2,000va / 192w max. switching current 10a min. switching load * 100 ma, 5 vdc life mechanical min. 5 x 10 6 operations electrical min. 50 x 10 3 operations coil data rated power (at 20 c) 220mw (24v coil, 250mw) 480mw operating temperature range -40 c to +70 c (no frost) timing data set / reset (at nominal coil voltage) max. 10ms (no bounce included) exitation time (at nominal coil voltage) min. 20ms insulation resistance (initial) min. 1,000mohm at 500vdc dielectric strength open contacts 1,000vac (50/60hz) 1min contacts to coil 5,000vac (50/60hz) 1min surge strength coil to contacts 10,000v / 1.2 x 50s standard wave clearance 8 mm creepage 8 mm other vibration resistance misoperation>1us 10 to 55hz double amplitude 2 mm endurance 10 to 55hz double amplitude 3 mm shock misoperation>1us min. 200m/s2 (11 1ms) endurance min. 1,000m/s2 (6 1ms) weight approximately 8 g
3 ftr-k1 series n coil rating coil code 1 coil 2 coils operating range coil resistance +/- 10% (ohm) operating range coil resistance +/- 10% (ohm) min. vdc max. vdc min. vdc max. vdc 3 2.4 5.4 41 2.4 5.4 19 5 4 9 114 4 9 53 6 4.8 10.6 164 4.8 10.6 75 9 7.2 15.9 368 7.2 15.9 169 12 9.6 21.2 655 9.6 21.2 300 24 19.2 42.2 2,304 19.2 42.2 1,200 note: all values in the table are valid for 20c and zero contact current. * specifed operate values are valid for pulse wave voltage. n characteristic data n reference data jsl series
4 ftr-k1 series n dimensions l dimensions unit: mm l pc board mounting hole layout (bottom view) l schematics (bottom view) jsl series jsl-m type l dimensions l pc board mounting hole layout (bottom view) l schematics (bottom view) jsl type l dimensions l pc board mounting hole layout (bottom view) l schematics (bottom view) jsl-dm type l dimensions l pc board mounting hole layout (bottom view) l schematics (bottom view) jsl-d type +/- = set, (+)/(-) = reset
5 ftr-k1 series 1. general information l all signal and power relays produced by fujitsu components are compliant with rohs directive 2002/95ec including amendments. l cadmium as used in electrical contacts is exempted from the rohs directives on october 21st, 2005. (amendment to directive 2002/95/ec) l all of our signal and power relays are lead-free. please refer to lead-free status info for older date codes at: http://www.fujitsu.com/us/downloads/micro/fcai/relays/lead-free-letter.pdf l lead free solder plating on relay terminals is sn-3.0ag-0.5cu, unless otherwise specified. this material has been verified to be compatible with pbsn assembly process. 2. recommended lead free solder profile l recommended solder sn-3.0ag-0.5cu. rohs compliance and lead free information 3. moisture sensitivity l moisture sensitivity level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. tin whiskers l dipped snagcu solder is known as presenting a low risk to tin whisker development. no considerable length whisker was found by our in house test. we highly recommend that you confrm your actual solder conditions flow solder condition: pre-heating: maximum 120?c soldering: dip within 5 sec. at 260?c solder bath jsl series solder by soldering iron: soldering iron temperature: maximum 360?c duration: maximum 3 sec.
6 ftr-k1 series japan fujitsu component limited gotanda-chuo building 3-5, higashigotanda 2-chome, shinagawa-ku tokyo 141, japan tel: (81-3) 5449-7010 fax: (81-3) 5449-2626 email: promothq@ft.ed.fujitsu.com web: www.fcl.fujitsu.com north and south america fujitsu components america, inc. 250 e. caribbean drive sunnyvale, ca 94089 u.s.a. tel: (1-408) 745-4900 fax: (1-408) 745-4970 email: components@us.fujitsu.com web: http://us.fujitsu.com/components europe fujitsu components europe b.v. diamantlaan 25 2132 wv hoofddorp netherlands tel: (31-23) 5560910 fax: (31-23) 5560950 email: info@fceu.fujitsu.com web: emea.fujitsu.com/components/ asia pacifc fujitsu components asia ltd. 102e pasir panjang road #01-01 citilink warehouse complex singapore 118529 tel: (65) 6375-8560 fax: (65) 6273-3021 email: fcal@fcal.fujitsu.com web: http://www.fujitsu.com/sg/services/micro/components/ fujitsu components international headquarter offces ?2011 fujitsu components europe b.v. all rights reserved. all trademarks or registered trademarks are the property of their respective owners. the contents, data and information in this datasheet are provided by fujitsu component ltd. as a service only to its user and only for general information purposes. the use of the contents, data and information provided in this datasheet is at the users own risk. fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. fujitsu components europe b.v. and affliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. nor do fujitsu components europe b.v. and affliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or ftness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. rev. march 24, 2011 jsl series
|
